How To Install A Chain Saw Blade
The chain saw blades are an essential part of the machine. To ensure that the blade works properly and does not cause any damage, they must be installed correctly. This article will show you how to install a chainsaw blade. There are a few simple steps that you need to take in order to get the job done right. We will also be providing tips on how to keep your chain saw blade in good condition. Lets get started! !
How To Install A Chain Saw Blade
How To Install A Chain Saw Blade.
Before installing a chainsaw blade, make sure it is off and unplugged. The reason for this is that it isnt safe to work on a running or plugged-in machine. You also dont want to get hurt doing the job because the machine suddenly turns on while you are working on it. It also needs to be cooled down before you get started because the saw will be hot in order to make the cutting easier.
You want to start by placing your thumb in the middle of the underside of your chain saw bar so that it is resting in place and wont move while you are adding the new blade. Then you need to pick up one half of your new chain saw blade with both hands and slip it into place just underneath your bar. Your teeth should be pointed downwards, or towards the place where you will actually cut wood with your machine. After that, you simply need to take a screwdriver and tighten the nuts down on top of each bolt until they are completely tight against both sides of the metal guide plate below. This is a process that you should do by hand, as an impact driver can cause the nuts to be loosened.
Once that is done, you need to make sure that the chain brake is pushed down in order to keep it from grabbing when you start up your machine again. Your blade should now be in its place and ready for use. If you take off a blade and put it on, you might have to reverse the steps. Thats all there is to know about how to install a chain saw blade!
Steps To Replace A Chainsaw Chain
Before you can replace a chainsaw chain, you need to make sure that the chainsaw is turned off and unplugged. It is unsafe to use a running or plugged in machine. You also dont want to get hurt doing the job because the machine suddenly turns on while you are working on it. It also needs to be cooled down before you get started because the saw will be hot in order to make the cutting easier.
Step 1: Take out the old chainsaw chain
To begin, insert your thumbnail into one of the holes in the rivet heads on the chainsaw chain. To begin removing the rivet, rotate your thumbnail counterclockwise. This will act as an anchor to ensure that the rest of it doesn’t move too much. Next, grab a pair needle-nose scissors and grasp the head of the rivet. This will allow you to twist the rivet completely from your saw blade. Repeat this step until all but one rivet is removed.
Step 2: Let go of the chain tension
Then, you can release the chain tension by inserting the end of your chainsaw saw bar into the slot in your saw base. Then, take a look at the guide bar which runs alongside it in order to determine where you need to place it so that it is overlapping all teeth equally. Grab your wrench and insert its curved tip between two teeth on both sides of the guide bar before turning them counterclockwise several times in order to release some chain slack. After doing this with just one side then do it to the other side as well before taking out the chain completely.
Step 3: Install Your New Chainsaw Chain
You can now install your new chainsaw chain by holding onto one end with your thumb and rotating it clockwise until it stops right before you get to the section of your guide bar where the rivets are. This will allow your guide bar to fit perfectly on the new chain. Next, grasp the ends of the chainsaw with one hand and the wrench in the second. Then insert the curved tip of the saw blade between the two teeth. Finally, turn the chain clockwise several times to tighten the chain. Once you have completed the first side, switch to the second side. Next, insert the curved tip of the wrench between the teeth on each side. Finally, tighten the screws with a pair or similar tools.
Step 4: Test your new chainsaw chain
After doing this then it is time to test your new chainsaw chain. Once everything is working properly, turn the chainsaw on. Although this step is not necessary, if the saw does not start up immediately you will need to adjust its tension. This can be done by either tightening or loosening the bar depending on how difficult or easy it was. Some owners choose to retighten their saw after using it several times in order to give it extra security against any problems down the line. However, each owner can decide what is best for them.
Step 5: Reinstall Your Old Chainsaw Chain
After you’re satisfied with the new chainsaw, you can remove it and reinstall it. Then turn on your chainsaw to check its performance. It won’t fix a broken chain, but it will make it cut through wood better.
Safety Tips
One thing which many people forget when installing their new chain saw blades is to properly lubricate each bolt before screwing it into place with the wrench. The reason for this is because if they dont the saw blade may become loose which is extremely dangerous. This can cause it to fly off while you are using the machine, so be careful to apply a small amount of WD-40 to each bolt before putting them into your guide plate where they belong.
You will need to loosen the three bolts that hold the blade of your chainsaw. However, you must not take them off yet. After that, take whatever tool you have at hand and push it down on the metal bar which runs alongside the chainsaw blade in order to lift up the chain. The last thing you want to do is use an impact driver because this can actually damage your new chain saw blade completely by stripping its nuts if they are tightened too much. To avoid injury, make sure your work area is clean before you start.
If your chainsaw blade is extremely dull, it could be that it cannot cut properly. To make your blade cut through wood more easily, you may need to sharpen it.
Final Thoughts
The chain saw blade has a round hole in the middle of it that should line up with the center of your bar. To install, youll need to use one hand to hold the end of the bar against your work surface and then push down on both ends of the blade until it clicks into place. Before you begin cutting wood, ensure that there is no slack between the ends of your gripping. If everything is good-to-go, start cutting!
